TOS5300 Series
よくあるご質問 閲覧ランキング
- 耐電圧（耐圧）試験って何ですか？
- 直流電源を接続する配電盤のブレーカ選定について教えてください。
- 検査票、試験成績書、校正証明書、トレーサビリティ証明書について教えてください。
- 電波法の高周波利用設備に該当する製品はありますか。
- VISAライブラリについて教えてください。
- ウォームアップ時間はどれくらいですか。
- 製品に電安法適用表示（PSEマーク）がありません。違法ではないですか。
- 耐電圧試験器を操作するために、必要な資格はありますか。
- PWR-01シリーズのPOWER スイッチをオンにしても動作しません。どうしたら良いでしょうか。
- 製品におけるPCB含有の有無について教えてください。
- マニュアル通りにコマンドを送っているのですが動作しません。どうしたらよいでしょうか。
- Is a current of approximately 40 μA at 1.8 kV normal for a custom AC withstanding voltage test jig using TOS5300 Series?
- Can TOS5300 series be controlled by a PLC in which the common terminals for input and output signals have different potentials?
- How can I get the IR test result when running the automatic test (AUTO TEST: IR → ACW)? I get the ACW result only if I send the RES? command.
- What is the function of the REMOTE connector on the front panel of TOS5300 series?
- How can I use both SIGNAL I/O and USB control on TOS5300 series and start the test with the SIGNAL I/O connector?
- Is there a polarity requirement when performing an insulation resistance test with TOS5302?
- How do I connect the optional high voltage test probe (HP01A-TOS or HP02A-TOS) to TOS5300 series?
- Why can’t I start a test when the READY LED lights up briefly and goes off after pressing the STOP switch on TOS5300 series ?
- What should I do when TOS5300 series shows “Calibration Protection” and cannot perform tests?
- What is DCW in TOS5300 series, and when is it used?
- For TOS5300 series, can I recall the panel memory when the system is in an interlock state under SIGNAL I/O control?
- Why does a Volt Error Protection occur during an AC (or DC) withstanding voltage test on TOS5300 series?
- How do I clear a USB Protection error on TOS5300 series?
- Why can’t I adjust the test voltage in 1 V steps on TOS5300 series?
- How can I check the current measurement when TOS5300 series passes a withstanding voltage test?
- When performing a withstanding voltage test with TOS5300 series, do I need to set a lower limit (LOWER) value?
- If TOS5302 displays a FAIL during an insulation resistance test, can I see the actual resistance measurement?
- How can I retrieve test results from TOS5300 series?
- Can I control TOS5300 series by a programmable logic controller (PLC)?
- I want to control TOS5300 series by a programmable logic controller (PLC). Can I connect the COM (circuit common) terminal of the TOS5300’s SIGNAL I/O connector to the COM terminal of the PLC’s +24 V internal power supply terminal?
- In the I/O connector of TOS5050, the INTERLOCK- terminal is connected to the COM (circuit common) terminal. Is it the same for TOS5302?
- Why is the INTERLOCK- terminal not connected to the COM (circuit common) terminal in the I/O connector of TOS5300 series?
- In TOS5300 series, there are two COM terminals of the SIGNAL I/O connector. Are they connected as the circuit common terminals or are they isolated?
